PMD-108-04
1 Flute Down Shear Polished Flute Carbide Router for Plastics and Aluminum
0.125-in Dia 1-Flute End Mill, 0.5-in LOC, 0.25-in Shank, 2-in OAL
Best tool for plastics — polished single flute that eliminates material sticking to the tool and melting in the cut.
- 1 flute polished-flute design gives the chip the whole gullet, so soft plastics evacuate before they can re-weld or melt in the cut
- PM = up-shear (pulls chips up and out, best general chip clearance); PMD = down-shear (pushes down on the material for clean top surfaces and thin sheet hold-down); GTS = 2 flute straight (0° helix) for materials that must not lift at all
- Tuffy grade carbide substrate
- PM sizes 1/8"-1/2" including long versions (PM-108-06L, PM-108-08L); PMD in 1/8", 3/16", 1/4"; GTS in 1/8"-1/2"
- Metric MPM up-shear from 4mm to 12mm
- Also the best tool for gummy/soft aluminum — polished flute reduces material sticking to the tool
- Tolerances: cutting dia +0.000/-0.002, shank dia -0.0001/-0.0002, flute length +0.060/-0.000, OAL +/-0.060
- Materials: plastics, wood, aluminum; dry, wet, cold air, or spray mist
From the RobbJack Applications Guide.
About this series
PMD Downshear Tuffy Grade Carbide Router Bits
Polished single-flute downshear router bits for aluminum.
The PMD series is a line of 1-flute Tuffy grade carbide router bits with a polished flute and square end, designed for downshear cutting in aluminum. Cutting diameters run from 1/8 inch to 1/4 inch.
- 1 flute
- Polished flute
- Square end
- Downshear geometry
- Tuffy grade carbide
Aluminum, Plastics, Wood. Dry, wet, cold air, or spray mist.
Headline spec
Cutting diameters 1/8 inch to 1/4 inch; 1-flute polished downshear router.
Best for
- Slotting
- Side Milling
- Helical Interpolation
- Ramping
- Roughing
- Semi-Finishing
- Finishing
Specifications
US machining terms with ISO 13399 codes.
- Cutting DiameterDC
- 0.125″
- Diameter ToleranceDC tol
- 0.0000/-0.0020
- Max Cutting DiameterDCX
- 0.125″
- Shank DiameterDMM
- 0.25″
- Length of Cut (LOC)APMX
- 0.5″
- Overall Length (OAL)OAL
- 2″
- Number of FlutesNOF
- 1
- Helix HandFHH
- Left-hand
- Cut Direction
- Right-hand cut
- Shank Blend Angle
- 15°
- End Type
- Square End
- Center Cutting
- Yes — plunges
- Shear Direction
- Down-shear
- Series
- PMD — 1 Flute Down Shear Polished Flute Carbide Router for Plastics and Aluminum
Cuts these materials
Applications
Features
See it run
Tolerances
| Type | Min | Max |
|---|---|---|
| Cutting Diameter | 0 | -0.002 |
| Length of Cut | +0.06 | 0 |
| Overall Length | +0.06 | -0.06 |
| Shank Diameter | -0.0001 | -0.0002 |
Made & shipped in the USA · lead time confirmed at order. Buy at retail or through your distributor.
Performance guaranteed. Run it against the tool you use today — if it doesn't beat it, we'll make it right.
Adds Uncoated · $57.25 — our pick for your material. Choose another finish below.
Proven in the field
- $548,290saved per year drilling carbon-fiber aircraft
- $216,000saved per year trimming aircraft skins
- 1,000%metal-removal increase in Inconel 718 (SPS)
Finishes (1)
Uncoated
PMD-108-04
$57.25
Available to order
Starting at
$57.25
Performance guaranteed
More in the PMD series
Same series, different size — what changes from this tool is shown in red.