MXF-602-10-020
6 Flute Standard Length High Performance Metric Carbide End Mill
10mm Dia 6-Flute Metric End Mill 20mm LOC, 10mm Shank, 72mm OAL, 2mm CR with Weldon Flats
OrderingMXF-602-10-020·Aluminum Titanium Nitride (AlTiN)·$171.10Change finish
6 and 8 flute, 45° helix Tuffy grade finishers for titanium, steels, and high-temp alloys — cut titanium up to 75 inches per minute.
- 6 flute (XF-602, 3/8"–3/4") and 8 flute (XF-802, 3/4"–1") Tuffy grade carbide with 45° helix, AlTiN coated
- Metric MXF line: MXF-602 in 10–16 mm and MXF-802 in 20–25 mm
- Corner radius on every tool — .030", .060", .090", .120" by size (metric 2.0, 2.5, 3.0 mm); no sharp-corner version
- Headline claim from the guide: cut titanium up to 75 inches/minute (1905 mm/minute)
- Materials: titanium, cast iron, steel, stainless steel, and super alloys up to 40 HRc hardness
- A dedicated side-milling finisher — applications are side milling, high-performance semi-finishing, and finishing (no slotting rating), run dry, wet, cold air, or spray mist
- XF finish profiling guidance: about .1 × diameter radial width at 1 × diameter axial depth; see the guide's trochoidal tool paths at robbjack.com/robbjack-tv
- Optional flats (-FL) on every inch size for high-torque holding; metric tools do not have flats
- Anti-pull-out h4 shank tolerance — tightest in the industry
- Tolerances: cutting dia −.001/−.002, shank −.0001/−.0002, flute length +.060/−.000 (MXF: cutting dia −.025/−.050 mm)
From the RobbJack Applications Guide.
About this series
MXF Metric Tuffy Grade Carbide End Mills
Metric high-flute-count finishing tools for steel & difficult alloys
MXF is the metric variant of the XF Series: 6-flute (MXF-602) and 8-flute (MXF-802) Tuffy Grade carbide end mills with 45 degree helix, AlTiN coated, 10-25 mm sizes. Metric tools do not have flats.
- 6 flute (MXF-602) and 8 flute (MXF-802) configurations
- 45 degree helix, square end with corner radius
- AlTiN coated
- Metric sizes 10 mm to 25 mm
- Metric tools do not have flats
Titanium, cast iron, steel, stainless steel and super alloys up to 40 HRc. Side milling, semi-finishing and finishing.
Headline spec
Metric 6/8-flute 45-degree-helix Tuffy Grade carbide, AlTiN coated
Best for
- Metric high-speed finishing
- Steel, stainless and difficult alloys
- Titanium
Specifications
US machining terms with ISO 13399 codes.
- Cutting DiameterDC
- 10 mm
- Diameter ToleranceDC tol
- -0.001/-0.002
- Shank DiameterDMM
- 10 mm
- Length of Cut (LOC)APMX
- 20 mm
- Overall Length (OAL)OAL
- 72 mm
- Corner RadiusRE
- 2 mm
- Number of FlutesNOF
- 6
- Helix AngleFHA
- 45°
- Helix HandFHH
- Right-hand
- Cut Direction
- Right-hand cut
- End Type
- Corner Radius
- Center Cutting
- Yes — plunges
- Series
- MXF-602 — 6 Flute Standard Length High Performance Metric Carbide End Mill
Cuts these materials
Applications
See it run · 2 videos
Tolerances
| Type | Min | Max |
|---|---|---|
| Cutting Diameter | -0.001 | -0.002 |
| Length of Cut | +0.06 | 0 |
| Overall Length | +0.06 | -0.06 |
| Shank Diameter | -0.0001 | -0.0002 |
Choose the finish(2 options)
Compare →Each finish is a different part number and price.
Part MXF-602-10-020
Made & shipped in the USA · lead time confirmed at order. Test this tool in your spindle at retail, or get it through your RobbJack distributor.
Performance guaranteed. Run it against the tool you use today — if it doesn't beat it, we'll make it right.
Adds MXF-602-10-020 · Aluminum Titanium Nitride (AlTiN) · $171.10
AlTiN
$171.10
MXF-602-10-020
Starting speeds & feeds for the MXF-602-10-020
Dial in for your machine →RobbJack's tested starting numbers for this exact tool, from the same engine and the same default machine as the calculator: a 12,000 RPM / 400 IPM / 30 HP machining center, rigid setup, full-depth cut. A faster or smaller spindle changes the RPM and feed — enter yours in the calculator and it re-governs every number.
| Material | Operation | SFM | RPM | Feed (IPM) | Chip load / tooth | DOC (in) | WOC (in) |
|---|---|---|---|---|---|---|---|
| 6AL-4V Titanium | Finishing | 380 | 3,687 | 19.9 | .00090 | .5906 | .0098 |
| Gray Iron | Finishing | 525 | 5,094 | 39.7 | .00130 | .5906 | .0098 |
| 4140 Steel | Finishing | 400 | 3,881 | 18.6 | .00080 | .5906 | .0098 |
Read before you run
Recommendations are computed starting points based on typical conditions — not guarantees of performance, tool life, or fitness for your application. Machining involves inherent risk: you are solely responsible for safe operation, for verifying every parameter against your machine, spindle, toolholding, workholding, and guarding limits, and for proving all parameters on a test cut before production. RobbJack Corporation assumes no liability for tool breakage, machine damage, scrapped parts, production loss, or personal injury arising from use of these recommendations. By using this calculator you accept RobbJack's Terms & Conditions.
More in the MXF-602 series
Same series, different size — what changes from this tool is shown in red.
- MXF-602-10-025$171.10CR 2.5 mmØ 10 mm6 FLLOC 20 mm
- MXF-602-10-030$171.10CR 3 mmØ 10 mm6 FLLOC 20 mm
- MXF-602-12-020$225.90Ø 12 mmLOC 25 mmOAL 83 mm6 FL
- MXF-602-12-025$225.90Ø 12 mmLOC 25 mmCR 2.5 mmOAL 83 mm
- MXF-602-12-030$225.90Ø 12 mmLOC 25 mmCR 3 mmOAL 83 mm
- MXF-602-16-020$481.45Ø 16 mmLOC 32 mmOAL 92 mm6 FL
- MXF-602-16-025$481.45Ø 16 mmLOC 32 mmCR 2.5 mmOAL 92 mm
- MXF-602-16-030$481.45Ø 16 mmLOC 32 mmCR 3 mmOAL 92 mm
- MXF-802-20-020$671.40Ø 20 mm8 FLLOC 38 mmOAL 104 mm
- MXF-802-20-025$671.40Ø 20 mm8 FLLOC 38 mmCR 2.5 mm
- MXF-802-25-020$864.60Ø 25 mm8 FLLOC 38 mmOAL 104 mm
- MXF-802-25-025$864.60Ø 25 mm8 FLLOC 38 mmCR 2.5 mm