M80-5000-22-30
80mm Diameter 22mm Arbor 30 Teeth Solid Carbide Saw for Non-Ferrous
80mm Diam. Slitting Saw, 5mm Thick, 22mm ID, 30 teeth
OrderingM80-5000-22-30·$902.20
Cutting deep slots? For slots deeper than 3× the saw thickness, the K-Series double-concavity version cuts cleaner and lasts longer. View the K-Series version (MK80-5000-22-30) →
About this series
Solid Carbide Slitting Saws
Tight widths and finishes HSS can't hold.
RobbJack solid carbide slitting saws are ground to ANY thickness up to 0.250" in 0.0001" increments — the listing shows common price-break thicknesses, but every size in between is standard. Coarse-pitch teeth suit non-ferrous materials and fine-pitch suit ferrous; standard-concavity covers general use, while K-series double-concavity, alternate-tooth-chamfer versions handle deep cuts.
- Any thickness up to 0.250" in 0.0001" increments — every size between the listed price breaks is standard
- Minimum thickness by diameter: 0.002" (3/4"–1"), 0.004" (1¼"–2"), 0.006" (2¼"–4"); K-series 0.020"
- Coarse pitch for non-ferrous, fine pitch for ferrous
- Standard and K-series double-concavity / alternate-tooth-chamfer versions
- Optional T-Process, hub, keyway and PVD coatings
- Thru-coolant saw systems available on NAB / AB arbors with CF flanges
Mounts on AB and NAB saw arbors. Choose K-series double-concavity saws for slots deeper than 3× the saw thickness.
Headline spec
Thickness tol +.0002/−.0000; diameter +.002/−.000
Best for
- Slotting & parting
- Tight-tolerance widths
- Ferrous & non-ferrous
Compatible saw arbors · 22 mm bore
NAB-875-TCRecommendedThru-coolant ultra-precision arbor — coolant straight to the cut · 25.4 mm shank
Max DOC *
20.518 mm
Ultra-precision arbor — 15× gripping force, lowest runout · 25.4 mm shank
Max DOC *
20.518 mm
Ultra-precision saw arbor · 19.05 mm shank
Max DOC *
22.855 mm
Metric ultra-precision saw arbor · 20 mm shank
Max DOC *
21.229 mm
Arbors that fit this saw's 22 mm arbor hole, recommended order first. * Max depth of cut = (saw diameter − arbor flange) ÷ 2, less a 0.050″ clearance cushion. Verify for your setup.
Specifications
US machining terms with ISO 13399 codes.
- DiameterDC
- 80 mm
- Saw Thickness
- 5 mm
- Arbor Diameter
- 22 mm
- Number of TeethNOF
- 30
- Max Depth of Cut (NAB-875-TC) *
- 20.523 mm
- Cuts
- Aluminum, Copper Alloy, Magnesium, Plastics, Composites
- Series
- M80-22-30 — 80mm Diameter 22mm Arbor 30 Teeth Solid Carbide Saw for Non-Ferrous
* Max depth of cut = (saw diameter − arbor flange) ÷ 2, less a 0.050″ clearance cushion. See per-arbor values below.
Cuts these materials
Features
See it run · 4 videos
Tolerances
| Type | Min | Max |
|---|---|---|
| Arbor Diameter | +0.005 | +0.01 |
| Concavity | +0.01 | 0 |
| Outside Diameter | +0.05 | 0 |
| Thickness | +0.005 | 0 |
Part M80-5000-22-30
Made & shipped in the USA · lead time confirmed at order. Test this tool in your spindle at retail, or get it through your RobbJack distributor.
Performance guaranteed. Run it against the tool you use today — if it doesn't beat it, we'll make it right.
Proven in the field
- $548,290saved per year drilling carbon-fiber aircraft
- $216,000saved per year trimming aircraft skins
- 1,000%metal-removal increase in Inconel 718 (SPS)
Need an in-between thickness?
Any thickness between this family's standard sizes is a standard order, not a special — the part number carries your exact thickness, priced as the next thicker catalog saw.
Volume pricing
| Qty | Uncoated |
|---|---|
| 3+ | $857.09 |
| 7+ | $811.98 |
| 25+ | $766.87 |
Uncoated: M80-5000-22-30
List price per piece at the ordered quantity — the cart and checkout both bill these tiers.
Starting at
$902.20
M80-5000-22-30
Starting speeds & feeds for the M80-5000-22-30
Dial in for your machine →RobbJack's tested starting numbers for this exact tool, from the same engine and the same default machine as the calculator: a 12,000 RPM / 400 IPM / 30 HP machining center, rigid setup, full-depth cut. A faster or smaller spindle changes the RPM and feed — enter yours in the calculator and it re-governs every number.
| Material | Operation | SFM | RPM | Feed (IPM) | Chip load / tooth | DOC (in) |
|---|---|---|---|---|---|---|
| 6061(T4-T6) Aluminum | Slitting / slotting | 3,600 | 4,366 | 52.4 | .00040 | .5000 |
| Free-Cutting Brass | Slitting / slotting | 1,000 | 1,213 | 14.6 | .00040 | .5000 |
| Acetal | Slitting / slotting | 1,600 | 1,941 | 23.3 | .00040 | .5000 |
Read before you run
Recommendations are computed starting points based on typical conditions — not guarantees of performance, tool life, or fitness for your application. Machining involves inherent risk: you are solely responsible for safe operation, for verifying every parameter against your machine, spindle, toolholding, workholding, and guarding limits, and for proving all parameters on a test cut before production. RobbJack Corporation assumes no liability for tool breakage, machine damage, scrapped parts, production loss, or personal injury arising from use of these recommendations. By using this calculator you accept RobbJack's Terms & Conditions.
Thru-Coolant NAB Precision Saw Arbor
Slitting saws fail when coolant can't reach the cut — external flood gets blocked by fixturing and part geometry. The NAB arbor delivers coolant through the center and out through thru-coolant flanges onto both faces of every saw — equal pressure, right where the cut happens. Precision-ground to 25 millionths and grips the saw up to 15× more tightly — so it can't slip or spin on the arbor — for faster speeds & feeds, no walking, and far longer tool life.
- 0.000025″
- tolerance — 25 millionths
- 15×
- grip on the saw vs. a typical arbor
- ≈80%
- fewer causes of saw failure
- ↑ S&F
- faster speeds & feeds, longer life
Recommended for your 0.8661″ bore saw
Contact application engineering for the thru-coolant arbor that fits this saw bore.
-TC arbors include steel thru-coolant outer flanges and steel spacers. Solid carbide flanges and spacers are recommended to eliminate burrs and potential issues — carbide lasts a lifetime and never scratches the saw. Add thru-coolant spacers to gang multiple saws.
Available in any thickness — 0.0079″ (0.2 mm) to 0.2362″ (6 mm)
This saw is stocked in 12 standard thicknesses, but any thickness between 0.0079″ (0.2 mm) and 0.2362″ (6 mm) is a standard order, not a special — you order in ten-thousandths of an inch and RobbJack grinds it, priced as the next thicker catalog size. Thickness is held to +.0002″/−.0000″, and the part number carries your exact thickness. Enter your size in the in-between thickness panel above to get the part number and price. Saws thinner than .010″ are specials and non-returnable. Ask your rep or distributor for current lead times.
More in the M80-22-30 series
Same series, different size — what changes from this tool is shown in red.
- M80-0200-22-30$368.350.2 mm thickØ 80 mm30T22 mm bore
- M80-0400-22-30$356.450.4 mm thickØ 80 mm30T22 mm bore
- M80-0600-22-30$350.200.6 mm thickØ 80 mm30T22 mm bore
- M80-1000-22-30$346.301 mm thickØ 80 mm30T22 mm bore
- M80-1200-22-30$356.901.2 mm thickØ 80 mm30T22 mm bore
- M80-1600-22-30$456.151.6 mm thickØ 80 mm30T22 mm bore
- M80-2000-22-30$489.802 mm thickØ 80 mm30T22 mm bore
- M80-2500-22-30$524.902.5 mm thickØ 80 mm30T22 mm bore
- M80-3000-22-30$663.553 mm thickØ 80 mm30T22 mm bore
- M80-4000-22-30$865.854 mm thickØ 80 mm30T22 mm bore
- M80-6000-22-306 mm thickØ 80 mm30T22 mm bore
- M80-0200-22-60$368.350.2 mm thick60TØ 80 mm22 mm bore